[CONSEIL] Flasher un Ericsson T68 en T68i

Okay, so I know people have had problems and have been anythign but thrilled with the T68i and some of the older Firmware... so I figred hey ill help everyone out and tell them just how simple and painless it is so they can do it themselfs! However I can not be held responsible in any way shape or form if for some reason your phone is damaged from or after this process. So read and do at your own risk.

**Note you may want to use various programs out there to backup your settings, phone book, data accoutns etc before proceeding as they will all get reset.**

1. Head on over to http://gsm.virtualdynamix.com/downloads.asp and pickup the remote log client and the SonyEricsson T68i Firmware Version R5C001.

2. Dust off yout trusty T28 data cable.

3. PayPal $15 to sales@virtualdynamix.com for you logger l/p.

4. Un-zip the logger into its own dir and for simplicity sake unzip the firmware files there too.

5. Run EricsClient.exe and first go to the settings tab and put in your username/password and make sure you have the correct com port selected. **NOTE: DO THIS FROM A CONNECTION FREE OF A FIREWALL/ROUTER/NAT/WIRELESS**

6. Then go to the Advanced Tab and in the "Flash:" box select "AVR Flash Chip".

7. Next click "Open SW" and select the "T68i_Avr.bin" and click "Open".

8. *** Make SURE this is set *** "Start Addr:" "0000-0000" "Length:" "0080-0000".

9. Power off your T68i and connect it to the data cable.

10. Click "Flash SW" and wait until it instructs you to "Power on the phone..."

11. Power on the phone as instructed... you will notice the software checking a few things and then a Firmware Update screen will appear with two percentage bars. Only the first one is going to display the progress and its going to take probably 20 or so minutes, considering its flashing 8 megs over serial its not too bad. Once it completes the bar will disappear.

12. DO NOT DISCONNECT OR POWER UP THE PHONE YET. Now under the "Flash:" option select "ARM Flash Chip"

13. Again click "Open SW" this time select "T68i_Arm.bin" and click "Open".

8. *** Make SURE this time it is set *** "Start Addr:" "0000-0000" "Length:" "0020-0000".

14. Again you will click "Flash SW" (I wasnt asked to power on the phone again but I suppose it could ask if you take too long and the connection times out). The progress bars will appears again and this time move much quicker as its only 2mb to flash instead of 8 this time.

15. For me when it completed the Status bar stayed up at 100% and I disconnected my phone, closed the program, powered it up and enjoyed my new R5C001 firmware!

Just a few notes, do not use the kill AVR option or for that matter any other options unless you know and fully understand what they can and will do. Use this process at your own risk but its what I did and it worked perfectly! I can try and answer any questions you may have, and im sure my friends at Virtual Dynamix will be more than willing to provide you with logins and passwords. As a side note I did have some difficulties at first trying to get the flashing process to begin. The software would check the username/password and return a message stating the "card" or card is full... I kept retrying after checking my settings as far as the software goes and after a few trys every now and then it worked. Also any type of firewall appears to block proper comunications with the server.

As far as notes go, I was running R3C001 on an unlocked AT&T phone, everything else should be explained in decent detail.

Happy Flashing!!! (Your phones that is )

oki c'ets le meme centre que pour siemens
j'y suis aller hier, elle sont passer les jolie nana la-bas que j'avais l'habitude de voir :cry: :cry: :cry: :?:
il font les mise à jour logiciel/fw ce que j'ai fait faire pour mon pote il etait en R2, merci pour l'astuce pour conaitre son fw.
pour ce qui est de la langue il disent qu'il peuvent pas la rajouter :cry:
bon j'aurais au moin mit a jour le fw, mais ça metra 48h contre 20min pour un siemens lol on se demande pq ???

Pour connaitre la version du soft de son Ericsson, il faut insérer le code suivant *>*<<*<*, dont > et < représentent les flèches ou le joystick à droite ou à gauche

Euh....bon c'est pas pour te proposer une solution, c'est juste pour une question

Ca vaut vraiment le coup de batailler comme ça ? Je veux dire, ça va changer quoi sur ton téléphone, vu que ça n'a pas l'air simple du tout ton histoire ?

nat, curieux parce que lui, les téléphones portable, ça sert juste à...téléphoner !!